Short Description

Model No.: ASTM-A312-EN-1.4404-Welded-Pipe-16"-SCH10-6M

China Welded Pipes Manufacturer www.pipelinedubai.com offers ASTM A312 EN 1.4404 Welded Pipe 16″ SCH10 6M.

Request a quote Share

Key Specifications / Features

Type: 1.4404 Welded Pipe
Material: TP316L (UNS S31603/EN 1.4404)
Size:

  • Outside diameter: 16″ (DN400/406.4mm)
  • Wall thickness: SCH10 (6.53mm)

Length: 6m (6000mm)

Chemical Composition and Mechanical Property For 316L
Steel Grade Chemical Composition Mechanical Performance
C(Max) Si(Max) Mn(Max) P(Max) S(Max) Ni Cr Mo N(Max) Tensile Strength Yield Strength
(Min) (Min)
Mpa Mpa
316L 0.03 0.75 2 0.045 0.03 10.0–14.0 16.0–18.0 2.00–3.00 0.1 485 170

Roughness of TP316l Stainless Steel Pipe

Surface Material Roughness Coeff.= ε in MM
Stainless Steel 0.015

Yield Strength of TP316l Stainless Steel Pipe

Grade Tensile Strength Minimum Yield Strength Minimum Elongation Minimum Hardness
Rockwell B Maximum Brinell Maximum
SS 316L 515 205 40 95 217

Equivalent Material of TP316l Stainless Steel Pipe

Grade UNS No Old British Euronorm Swedish SS Japan Industrial Standard
British Standards European Standards Werkstoff no Name
316L S31603 304S11 58E 1.4436 X3CrNiMo17-13-3 2348 SUS 316L

Physical Properties of TP316l Stainless Steel Pipe

Grade
Density Elastic Modulus Mean Coeff. of Thermal Expansion Thermal Conductivity Specific Heat 0 To 1000C Electrical Resistivity
0 To 1000 C 0 To 3150 C 0 To 5380 C at 1000 C at 5000 C
316L 8000 193 15.9 16.2 17.5 16.3 21.5 500 740

Steel pipe wall thickness (ASME B36.10 & B36.19)

Nominal Pipe Size Outside diameter Wall thickness
SCH 5S SCH 10S SCH STD (40S) SCH XS SCH 160S SCH XXS
(80S)
1/8″ 10.29 1.24 1.73 2.41
1/4″ 13.72 1.65 2.24 3.02
3/8″ 17.15 1.65 2.31 3.2
1/2″ 21.34 1.65 2.11 2.77 3.73 4.75 7.47
 3/4″ 26.67 1.65 2.11 2.87 3.91 5.54 7.82
1″ 33.4 1.65 2.77 3.38 4.55 6.35 9.09
1 1/4″ 42.16 1.65 2.77 3.56 4.85 6.35 9.7
1 1/2″ 48.26 1.65 2.77 3.68 5.08 7.14 10.16
2″ 60.33 1.65 2.77 3.91 5.54 8.71 11.07
2 1/2″ 73.03 2.11 3.05 5.16 7.01 9.53 14.02
3″ 88.9 2.11 3.05 5.49 7.62 11.13 15.24
3 1/2″ 101.6 2.11 3.05 5.74 8.08 16.15
4″ 114.3 2.11 3.05 6.02 8.56 13.49 17.12
5″ 141.3 2.77 3.4 6.55 9.53 15.88 19.05
6″ 168.28 2.77 3.4 7.11 10.97 18.24 21.95
8″ 219.08 2.77 3.76 8.18 12.7 23.01 22.23
10″ 273.05 3.4 4.19 9.27 12.7 28.58 25.4
12″ 323.85 3.96 4.57 9.53 12.7 33.32 25.4
14″ 355.6 3.96 4.78 9.53 12.7 35.71
16″ 406.4 4.19 4.78 9.53 12.7 40.46
18″ 457.2 4.19 4.78 9.53 12.7 45.24
20″ 508 4.78 5.54 9.53 12.7 49.99
22″ 558.8 4.78 5.54 9.53 12.7 53.97
24″ 609.6 5.54 6.35 9.53 12.7 59.51
The dimensions are in millimeters
Sources : ASME B36.19, ASME B36.10

Pipes Diameter Tolerance

PIPE NPS/ DN/ OD Allowed Outside Diameter Tolerance
Over Under
inches mm inches mm
NPS 1/8 to 1½ 1/64 0.4 1/64 0.4
DN 6 to 40
OD 10.3 to 48.3, mm
Over 1½ to 4 1/32 0.8 1/32 0.8
DN 40 to 100
OD 48.3 to 114.3 mm
Over 4 to 8 1/16 1.6 1/32 0.8
DN 100 to 200
OD 114.3 to 219.1 mm
Over 8 to 18 3/32 2.4 1/32 0.8
DN 200 to 450
OD 219.1 to 457 mm
Over 18 to 26 1/8 3.2 1/32 0.8
DN 450 to 650
OD 457 to 660 mm

Pipes Thickness Tolerance

PIPE NPS/ DN/ OD Tolerance, % from Nominal
Over Under
NPS 1/8 to 2½, all t/D ratios 20 12.5
DN 6 to 65
OD 10.3 to 73.0, mm
NPS 3 to 18, t/D up to 5% 22.5 12.5
DN 80 to 450
OD 88.9 to 457 mm
NPS 3 to 18, t/D > 5% 15 12.5
DN 80 to 450
OD 88.9 to 457 mm
NPS 20 and larger, welded, all t/D ratios 17.5 12.5
DN 500
OD 508 mm
NPS 20 and larger, seamless, t/D up to 5% 22.5 12.5
DN 500
OD 508 mm
NPS 20 and larger, seamless, t/D > 5% 15 12
DN 500
OD 508 mm

Pipes Weight Tolerance

  • The pipes’ weight tolerance depends on the nominal pipe size, as listed below:
  • Pipe of NPS 4 (DN100, 114.3mm) and smaller may be weighed in convenient lots; pipe in sizes larger than NPS 4 shall be weighed separately.
  • Pipes NPS 12 (DN300, 323.8mm) and under, weight tolerance is: -3.5% / +10%.
  • Pipes over NPS 12 (DN300, 323.8mm),weight tolerance is: -5% / +10%.

Pipes Quantity Tolerance

  • Should be within -10% to +10% tolerance, as a rule of thumb (-3/+3% should be acceptable).

Pipes Length Tolerance

  • Seamless and Welded (no filler metal added): if cut lengths are ordered, no length of pipe shall be under the length specified and not more than 1/4 in. (6.35 mm) over that specified.
  • Forged and Bored, Cast, and Cast Cold-Wrought: if definite cut lengths are ordered, no length of pipe shall be under the length specified and not more than 1/8 in. (3.2 mm) over that specified.
  • For pipe ordered to random lengths, the lengths and variations shall be agreed upon between the manufacturer and the buyer.

NPS to DN Conversion Chart

The table shows the conversion between NPS and the pipe outside diameter in inches, mm and DN (nominal diameter):

PIPE NPS Pipe outside diameter PIpe outside diameter NPS to DN
in inches in mm conversion
1/8 0.404 10.26 6
1/4 0.54 13.72 8
3/8 0.675 17.15 10
1/2 0.84 21.34 15
¾ 1.05 26.67 20
1 1.315 33.4 25
1 ¼ 1.66 42.16 32
1 ½ 1.9 48.26 40
2 2.375 60.33 50
2 ½ 2.875 73.03 65
3 3.5 88.9 80
3 ½ 4 101.6 90
4 4.5 114.3 100
4 ½ 5 127 115
5 5.563 141.3 125
6 6.625 168.28 150
7 7.625 193.68
8 8.625 219.08 200
10 10.75 273.05 250
12 12.75 323.85 300
14 14 355.6 350
16 16 406.4 400
18 18 457.2 450
20 20 508 500
22 22 558.8 550
24 24 609.6 600
26 26 660.4 650
28 28 711.2 700
30 30 762 750
32 32 812.8 800
34 34 863.6 850
36 36 914.4 900
38 38 965.2 950
40 40 1016 1000
42 42 1066.8 1050
44 44 1117.6 1100
46 46 1168.4 1150
48 48 1219.2 120

China Welded Pipe Manufacturer www.pipelinedubai.com offers ASTM A312 EN 1.4404 Welded Pipe 16″ SCH10 6M.

Request a quote

    Subject:

    Products Related to ASTM A312 EN 1.4404 Welded Pipe 16″ SCH10 6M