Short Description

Model No.: UNS-N10675-Stub-End-Short-Pattern-DN32-Sch10S

China Lap Joint Stub End Manufacturer www.pipelinedubai.com offers ASME B16.9 ASTM B366 UNS N10675 Stub End, Short Pattern, DN32, Sch10S.

Request a quote Share

Key Specifications / Features

Type: UNS N10675 Stub End
Material: Hastelloy B3 (UNS N10675/W.Nr.2.4600)
Size: 1-1/4″ (DN32)
WT: Sch10S
Standard: ASME B16.9

20201026093716 77609 - ASME B16.9 ASTM B366 UNS N10675 Stub End Short Pattern DN32 Sch10S

Chemical Composition of Hastelloy B3 (UNS N10675)

Ni Mo Fe C Co Cr Mn Si Ti W Al Cu
65.0 min 28.5 1.5 .01 max 3.0 max 1.5 3.0 max .10 max .2 max 3.0 max .50 max .20 max

Equivalent Grades of Hastelloy B3 (UNS N10675)

Trademarks GB JIS KS ASTM UNS DIN W.Nr GOST BS NF
Hastelloy B-3 NS3203 Hastelloy B-3 N10675 NiMo29Cr 2.46

Physical Properties of Hastelloy B3 (UNS N10675)

Density
(g/cm3)

Melting Point
(℃)

Electric resistivity 
(µΩ·cm)

Coefficient of thermal expansion 
10-6K-1(20-100℃)

Elastic modulus
(GPa)

Hardness (Brinell)/HB

Operating temperature
(°C )

9.22

1418

137

10.6

216

94

 -200 – +400

Mechanical Properties of Hastelloy B3 (UNS N10675)

Annealed

  • Heat Treatment: 2100°F (1150°C)
  • Tensile Strength: 110 ksi (760 MPa) min 125 ksi (860 MPa) typ
  • Suggested Operating Conditions: -300°F to 1800°F (-184°C to 900°C)

lap joint stub end dimensions - ASME B16.9 ASTM B366 UNS N10675 Stub End Short Pattern DN32 Sch10S

Lap Joint Stub End Metric Dimensions as per ASME B16.9

NPS ODMax ODMin LPF SPF R G
1/2″ 0.896 0.809 3 2 0.12 1.38
3/4 1.106 1.019 3 2 0.12 1.69
1 1.376 1.284 4 2 0.12 2
1-/1/4 1.716 1.629 4 2 0.19 2.5
1-1/2 1.965 1.869 4 2 0.25 2.88
2 2.456 2.344 6 2.5 0.31 3.62
2-1/2 2.966 2.844 6 2.5 0.31 4.12
3 3.596 3.469 6 2.5 0.38 5
3-1/2 4.096 3.969 6 3 0.38 5.5
4 4.593 4.469 6 3 0.44 6.19
5 5.683 5.532 8 3 0.44 7.31
6 6.743 6.594 8 3.5 0.5 8.5
8 8.743 8.594 8 4 0.5 10.62
10 10.913 10.719 10 5 0.5 12.75
12 12.913 12.719 10 6 0.5 15
NPS ODMax ODMin LPF SPF R G
14 14.17 13.969 12 6 0.5 16.25
16 16.18 15.969 12 6 0.5 18.5
18 18.19 17.969 12 6 0.5 21
20 20.24 19.969 12 6 0.5 23
22 22.24 21.969 12 6 0.5 25.25
24 24.24 23.969 12 6 0.5 27.25

GENERAL NOTES:

  • (a) All dimensions are in millimeters.
  • (b) See Table 1 for tolerances.
  • (c) Service conditions and joint construction often dictate stub end length requirements. Therefore, the purchaser must specify long or short pattern fitting when ordering.

NOTES:

  • (1) Gasket face finish shall be in accordance with ASME B16.5 for raised face flanges.
  • (2) The lap thickness T shall not be less than nominal pipe wall thickness. See Table 1 for maximum tolerance.
  • (3) When short pattern stub ends are used with larger flanges in Classes 300 and 600, with most sizes in Classes 900 and higher, and when long pattern stub ends are used with larger flanges in Classes 1500 and 2500, it may be necessary to increase the length of the stub ends in order to avoid covering the weld with the flange. Such increases in length shall be a matter of agreement between the manufacturer and purchaser.
  • (4) When special facings such as tongue and groove, male and female, etc., are employed, additional lap thickness must be provided and such additional thickness shall be in addition to (not included in) the basic length F.
  • (5) These dimensions conform to the radius established for lap joint flanges in ASME B16.5.
  • (6) This dimension conforms to standard machined facings shown in ASME B16.5. The back face of the lap shall be machined to conform to the surface on which it seats. Where ring joint facings are to be applied, use dimension K as given in ASME B16.5.

Dimensional Tolerances of Stub Ends ASME B16.9 (Table.1)

Nominal Pipe Size 1/2 up to 2½ 3 to 3½ 4 5 to 8 10 to 18 20 to 24
Outside Diameter at Welding End (OD)
+ 1.6
– 0.8
1.6 1.6
+ 2.29
– 1.6
+ 4.06
– 3.05
+ 6.35
– 4.83
Overall Length (F) 1.6 1.6 1.6 1.6 2 2
Outside Diameter of Lap (G)
+ 0
– 0.76
+ 0
– 0.76
+ 0
– 0.76
+ 0
– 0.76
+ 0
– 1.6
+ 0
– 1.6
Thickness of Lap (T)
+ 1.52
– 0
+ 1.52
– 0
+ 1.52
– 0
+ 1.52
– 0
+ 1.52
– 0
+ 1.52
– 0
Fillet Radius of Lap (R)
+ 0
– 0.76
+ 0
– 0.76
+ 0
– 1.6
+ 0
– 1.6
+ 0
– 1.6
+ 0
– 1.6
Wall Thickness (t) Not less than 87.5% of Nominal Wall Thickness

  • Dimensional tolerances are in millimeters unless otherwise indicated.

Request a quote

    Subject:

    Products Related to ASME B16.9 ASTM B366 UNS N10675 Stub End Short Pattern DN32 Sch10S